It’s been a while… 😛

I did some minor adjustment, ditched the VHST28 and AM6 Vforce. Adapted the engine to KX85 Vforce3 with VHSH 30mm carb.. Dyno the engine to 27hp on the rear wheel.
Tried on 201 meter, but the cylinder studs that goes through the carter also transported cooling water into the cylinder, so the engine ran very badly.

Now I…[Lees meer]

I got my 2 Polini gearboxes now.
One built with old-type Malossi gearsand the second one with polini gears.

There is alot of friction with the Malossi gears, worst every third-ish turn on primary but overall, too much friction. Some parts nott possible to turn shaft by hand, but easy with wrench.

The one with Polini gears is  very very smooth.…[Lees meer]

Thanks! 2 hubs ordered 😀

Hello Jelle and TW1 – I see that you have been testing out the Polini gearbox and it seems overall you were satisfied in August. Haven’t ran into any troubles yet?

This forum is among others replaced with facebook, whatsapp and other platforms. I guess more people in NL have tried the gearbox along with the Malossi. Whats peoples opinions today?…[Lees meer]

Sproeier Database Behandelt alleen oude DEPS.
Mijn motor is vol Malossi, DEPS 2019 3p, PHBG 19mm – kompressietest leven 10.5Kg
Vario met Malossi 1:9 + Malossi koppeling (102mm)

Ik heb het gevoel dat de kracht aan de top ontbreekt. Het wil niet zo veel variëren als ik rij, maar als het op de steun staat varieert het volledig.

Sproeier is 92.
3%…[Lees meer]

PM

Uppgraded to hydraulic rear brakes.
Not the Italy version, but instead the German version which gives the oppertunity to use rotors made for example KTM, Husqvarna, Husaberg. I went with Brembo originals.

M10x1,25

I have the “PVR” pullstrter for mine. The nut is availble with M8 (standard) and M10 (Malossi).
Depending on how your nut is designed, you can drill it and remake the threads with M10 instead.
If you want to take the easy way out you can buy the parts frrom Italy, contact “Paolo Pvr” on Facebook.

We’ve had helmplicht in Sweden since 1978, think it saved a lot of lives over the years 🙂
At VCM 2019 I was kind of surprised that helmet wasn’t used more often 😀
For me, use of helmet is just as natural as bushing teeths in the evening, but then again it’s been mandatory all my life.

Didn’t manage to get rid of the false air / idle issue last year.. So I have split the carter and remade the gasket, hopefully this will solve the high idle issue.. Running 92 JET, so it can’t be a problem with that.
Interestering to see if there’s still a vacuum issue with air in the hose.

Also overtightened the top manifold screw last year, to…[Lees meer]

Peter-swe wrote:
Yes, imports! Happened in the course of about 6 months – I looked at the ones in NL but could not find the way to get the ones from marktplaats 🙂 The moment I started looking for local ones, prices here in Swe went absurd. Where are you located if no secret?

Stockholm/Tyresö, no secret. 🙂
Parts are often no problem to buy at Ma…[Lees meer]

Hi Peter,

I guess you’ve imported thoose mix-ciaos to Sweden? Since they weren’t sold on our market.
No licence plate required as you state, but you still need the “typintyg” for the mopeds to be road legal.
Not saying that I following that very strictly at all, but tecnically it’s in the books. 🙂
Thoose who attended VCNL meet 2019 might…[Lees meer]

Thanks!

Hmm, is the regulator 2 independant channel? Since you have both Yellow and Red from the Malossi stator going into the regulator.
I thought the regulator only could handle 1 input?

You are correct, Previous owner messed with my wiring harness earlier. The stator colors are still intact, so those colors are matching the Diagram.

Yes, the Malossi regulator.

If I’m not mistaken, yellow and blue are positive (+) and brown is ground (-) and also the single cable that normally grounds to the engine block is ground/negative.

I…[Lees meer]

Case closed!

Tank is almost cleaned, used degreaser first and flushed it.
After that Citric Acid in the tank for 36h followed by a good flush. At first it was Semi-good flow, after a couple of litres the flow increased and the tank swallowed almost full capacity of the hose.

No I have put a dishwasher tablet to neutralize the remainings of the Acid, will…[Lees meer]