My great-grandfathers walking stick was totally full with emblems of where he was on tour. So I thought “Why shouldn’t we do something similar with our Mopeds?” So I just designed a little emblem which we can make as a sticker/patch. It could look like this or (slightly) different. Tipps or wishes are welcome, so I can make the stickers a month…[Lees meer]

The kick Evo Engine is nice! But why the 46,5 Malossi on it? The other projects are nice, too! I like the grey CBA, it’s stylish.

Leuke brommer! Very nice Setup tho. Can you say something to the performance of the 42mm Polini?

210 ex op de Simo LC Kit

Please also add llincoln from PMT. He has a nice and reliable Ciao which easily hits the 65 km/h.

EDIT: Ciao-Racer-sg wants to take part, too. Would be nice if you can put him to the list, too.

Please count me in. I am looking forward to it!

It is nice to see how much dutch people appreciate the old Ciaos and try to keep them in original state. Keep on!
The look of the red one on the top is nice, too. Reminds me to the Vespa 50 SS

Nice speedometer. I like the original look and that you don’t saw up such a beauty to realize stupid engine setups and experiments, like a Simo in oldie frames with 19″ wheels. :thumb

Plenty friends drive the Gianelli Street exhaust and it is really good!

I personally like the short Sito (with E-number). It does by far not have the high rpm power but is good in the lower and middle areas. I drive it on my original engine and it easily goes 38 km/h GPS with it and even 12% are no problem with 30+.

I really appreciate this advice! Thank you, mates. I just dismounted the wheels to get rid of the Newfren brakes.
I have seen the rear brakes here, but where can I get Ferodo (or other good manufactor’s) brakes for the front wheel with 90mm housing?

Here’s just some wierd stuff of my detail-keenness. 😀

Alu cilinder cover:

Original…[Lees meer]

Alright, thank you! Can you please tell me what’s wrong with the Newfren brakes? Just out of interest..
Luckily I did not drove this much and fast yet.

This reminds me to the Delorean dmc-12. I like this project, everything is quite coherent. :thumb

Thanks for the advice!
Why do they mess up the Mozzis from the inside? So you would take the original brakes?

To mount the Pinasco springs was horrible. I did not expect them to be that hard.. You better fit them in with a buddy.

PS. To srew in the Pinasco springs I was forced to mill the other parts a bit. Otherwise they did not fit in.…[Lees meer]

@ ritze: I hope so! 🙂 Thank you! The inlet is ported as in my VCT ’09 / ’14 engine which still runs good. The “blow-through test” was alright, too, and the engine runs nice. So I don’t worry.

@ Crullie: Thanks! You do not have to wait long. 😉

FRAME

After the parts were sandblasted I wanted to paint them with the original ’55 300 SL…[Lees meer]

@ Edjuh: Thank you! It was mainly made by MofaFreak.

Here are some impressions from the engine:

The ports open well and the piston exactly leaves the whole outlet port free. :thumb

The engine did run the first kms but is dismounted yet, because I will try to make an electronic ignition out of the…[Lees meer]

Can anyone please shortly explain in English why you cut the cilinder socket?:o
I can’t see any plausible reason to do that… especially not an a rare Eurocilindro! :'(
I think it is a better idea to weld it and cover it with a new nikasil coat. Otherwise, I would take the cilinder, Andree.:D

It’s not intended to cut the cylinders, but these…[Lees meer]

Jockoballa en MofaFreak87

I’m very sorry, but I´m out. Unfortunately it´s not possible for me to come with you..
Have a lot of fun and I hope you won’t have any brakedowns!
See you at the VCT! :thumb

Ik hoop! :thumb Ik denk dat hij reed een Polini of Malossi 43mm.
We weten niet precies wat er mis is met Nuckelchen. Hij was niet online over 3 jaar en 9 maanden…

Ik denk over rijden en 43mm Eurocilindro.. als dat intelligent?? 😕

That’s the point! 79 is the current price all inkl.. But in fact this offer is not endlessly valid I would like to order, soon.