jodojodo :
Hi Dejan
I do own a Gilera CBA. I will check tonight if i can provide you
with the requested data

This will be great:)

Last Friday I have been also tried to contact “Batty” with the same message (send to PM) but I didn’t receive any answer.

Thanks for helping me in advance…

ritze :
your pipe is good for a 50cc stock setup. normally youll have to fit a jet between 50 and 56 with a 12.12
check your sparkplug for color after 20 km, it has to have a dark brown color

what do you think about the Polini air filter in my set up? should I change it with the original piaggio one (DGM)

Best regards

Hello,

I have very good experience with DAYCO vario belt special for PIAGGIO SI. I also have Piaggio model SI vario with 90 mm pulley and I have never had any problems with lenght. Here ’s the link from the store where I bought it.…[Lees meer]

What about the benefits which I could gain with LEO VINCE circuit (acceleration, torque, top speed) according to the GIANNELLI city power?

What about the central stand. Is it neccesary to dismount the central stand for proper mounting of LEO VINCE circuit?

My question about GIANNELLI city power was more about the benefits which I could gain with LEO VINCE circuit (acceleration, torque, top speed) according to the GIANNELLI city power?

Regards

Martino :
From some sort off quiet till loud; Leovinci, Polini, Proma.

But keep in mind, there is some difference between the Leovinci silencers. Unfortunately there’s no picture with the provided link. Thanks for the link between. :thumb

What do you excatly mean with this differences about LEOVINCE silencers. I also missing the picture…[Lees meer]

Hello,

I found LEO VINCE new model 4234 (CIAO version) on MOPSHOP store (Germany).It seem to be a reasonable price:)Here’s the link

http://www.mopshop.de/shop/Moped-Mofa-Piaggio-Ciao-PX-Rennauspuff-LeoVince-kpl-4234-ohne-E-Gutachten-Zylinder-Anschluss-22mm-p-441_496_499_10_19670.html

I also wonder if it is neccesary to dismount the…[Lees meer]

Hello,

Is there any chances that you send me some pictures of VARIO that you sell to and would you shipp to SLOVENIA (cost)?
Please send a PM.

regards

Thank you for the exact explanation:).

If I understand the chart I must look for details in row 8 (1:10,5) gearing 10.73?

Nice chart, but I need some explanation:con

Thanks to all of you for the comments.:thumb

I would certainly go for original Piaggio 1:10,5 gearing, if I could get one:con

Is there any other way beside that you turn the rear wheel and count the revolutions to be sure that I get the right one 1:10,5 gearing. If I dismount the vario gear hub and count the numbers of tooth on the gear wheels?

Do you think that with this set up malossi gearing (1:9) would’t be too hard. What about some bad experiences with CIF gearing – bad quality?

1 : 12.5, but I have already open a new topic because now I have different set up – look in forum> (English)> (English) The bar> Top speed according to the setup

Sorry for may late response, I have 1:12.5 gearing. Yesterday I was also put mixed 3x6g and 3x7g rolls (average 6,5 g) but the top speed remains around 60 KM/h (GPS) only the acceleration is maybe a little bit better. I assumed that with my gearing (1:12.5)I’ve already reach the limit:(

Do you think I must looking for gearing MALOSSI 1:9…[Lees meer]

Do you mean by this if the roller weights are too light it variates too fast and vice versa too slow with heavier rolls?

:con

Today I have installed 6x 7g roller weights. Top speed is raising to 61 km/h. Should I go little bit down, maybe 3x 6g and 3x 7g?

Niek1992 thanks for the suggestions.:thumb Is it wise that you mix the 6g and 9g or 7g and 9g roller weights?

Anyone else have maybe another opinion.

regards

Hello,

At home I have complete of 6 g, 7g and 9 g roller weights sets. Do you suggested me that I maybe mix 3×7 g and 3x9g or ??
:thumb

Thank you for answer,:thumb

I will follow your instructions if I would buy gianelli fire.

regards

– What about Polini top one or Simonini proline. Do they fit on SI without modification?

– I have read that there were some problems with Gianelli fire (SI model), breaking the holder (bolt for fixing the
motor). Is there any tip for proper